Done!
The thing was the IP on the special tab (have to enter the lowest one) and the local start
Thanks for all the help!
NanoKontrol 2 Why doesn't recognize the midi input?
-
- Posts: 7
- Joined: Thu Jan 07, 2016 8:29 pm
Re: NanoKontrol 2 Why doesn't recognize the midi input?
10.0.0.1 must be entered in the "special" tab under local ip.
i would recommend to use an other GMA universe than 1 (local start) i personally prefer 4 or 5 which does not collide with a wing or node.
maybe bomac values are overwritten by an other dmx input or by channels.
MA says: it's not recommend to use WIFI.
Are you using a wing? If so you need to use a broadcast address and you need to install a network loopback adapter.
Did you saw this instructions for wings?
i would recommend to use an other GMA universe than 1 (local start) i personally prefer 4 or 5 which does not collide with a wing or node.
maybe bomac values are overwritten by an other dmx input or by channels.
MA says: it's not recommend to use WIFI.
Are you using a wing? If so you need to use a broadcast address and you need to install a network loopback adapter.
Did you saw this instructions for wings?
f you have no network devices connected to your laptop/pc [for MA-Users: if you are using a wing only (no 2port-/4port-/8port-nodes,nsp etc.)] you may need to install microsoft's loopback adapter to assign an Art-Net IP to that virtual network card. working network is required for Art-Net. You need to use a broadcast IP, when your software doesn't receive the DMX values. http://technet.microsoft.com/en-us/libr ... 10%29.aspx
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Hi There,
I've try many times but despite the help brought me this topic i can't use Bomac too !
All be connected but in DMX sheet any values is moving on ... what i've missing ?
Setup :
Bomac Free
NanoKontrol 2
GMA2 3.1.2.5
Virtual Card Ethernet with 2 IP 10.0.0.2 to Bomac / 11.0.0.2 to MA
Thx in advance
Fritz,
I've try many times but despite the help brought me this topic i can't use Bomac too !
All be connected but in DMX sheet any values is moving on ... what i've missing ?
Setup :
Bomac Free
NanoKontrol 2
GMA2 3.1.2.5
Virtual Card Ethernet with 2 IP 10.0.0.2 to Bomac / 11.0.0.2 to MA
Thx in advance
Fritz,
Re: NanoKontrol 2 Why doesn't recognize the midi input?
11.0.0.2 (to MA) is not an valid Art-Net IP. Art-Net is 2.x.x.x or 10.x.x.x but never 11.x.x.x !
Use 10.0.0.2 and 10.0.0.254 to be safe.
Subnet mask ist 255.0.0.0!
Use 10.0.0.2 and 10.0.0.254 to be safe.
Subnet mask ist 255.0.0.0!
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Hi Bernd,
Thank's for tip at moment i've put 10.0.0.254 to the Grandma network session and 10.0.0.2 at your software and nothing changed but the session status is Slow .. maybe ?
See you
Thank's for tip at moment i've put 10.0.0.254 to the Grandma network session and 10.0.0.2 at your software and nothing changed but the session status is Slow .. maybe ?
See you
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Did you enabled Art-Net input?
Is a session started?
Does DMX-Workshop shows the listening ports of the GMA2?
Is a session started?
Does DMX-Workshop shows the listening ports of the GMA2?
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Hi,
Yes Artnet input is active and session started ! in DMX sheet any values from bomac are detected..
Yes Artnet input is active and session started ! in DMX sheet any values from bomac are detected..
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Which DMX-sheet?
That one in GMA2 or the bomac one?
If you talking about the gma2 one i don't understand the problem.
steps left are only
- go to setup
- remote input dmx
- must be enabled
- assign what ever you want
- done
see video
https://youtu.be/ATwjqJsLoL4?list=PLAzO ... 8d8S&t=334
That one in GMA2 or the bomac one?
If you talking about the gma2 one i don't understand the problem.
steps left are only
- go to setup
- remote input dmx
- must be enabled
- assign what ever you want
- done
see video
https://youtu.be/ATwjqJsLoL4?list=PLAzO ... 8d8S&t=334
Re: NanoKontrol 2 Why doesn't recognize the midi input?
I'have made a quick video
let you see the problem https://www.youtube.com/watch?v=BiHXO_f ... e=youtu.be
let you see the problem https://www.youtube.com/watch?v=BiHXO_f ... e=youtu.be
Re: NanoKontrol 2 Why doesn't recognize the midi input?
Great video, thank you. that helped me alot.
You have discovered a bug, in grandma version 3.1.2.5.
First, required and no bug:
In bomac - project settings - go to special tab and enter the second lower Art-NET IP you have assigned to you network-adapter.
As in my sample 10.0.0.2
Second - the bug in GMA2:
You have chosen amount of 4 and start universe "D".
In hexadecimal you are count 0-9, a,b,c,d,e,f.
Amount of 4 need D,E,F of subnet 0 and a next value. Next value in this case is it a subnet higher (1) and universe starting at 0.
In this case GMA2 onPC version 3.1.2.5 sends a wrong subnet.
To compare it with bomac i have also started dmx-workshop.
See screenshot, please.
You need to correct it back to subnet 0, after you have chose it from that selection!
Or reduce the Amount to 3, to stay on letter F as biggest.
I will send MA a bug report.
Correct would be Art-Net addresses which where expected from bomac (which gma does not send):
0.D
0.E
0.F
1.0
You have discovered a bug, in grandma version 3.1.2.5.
First, required and no bug:
In bomac - project settings - go to special tab and enter the second lower Art-NET IP you have assigned to you network-adapter.
As in my sample 10.0.0.2
Second - the bug in GMA2:
You have chosen amount of 4 and start universe "D".
In hexadecimal you are count 0-9, a,b,c,d,e,f.
Amount of 4 need D,E,F of subnet 0 and a next value. Next value in this case is it a subnet higher (1) and universe starting at 0.
In this case GMA2 onPC version 3.1.2.5 sends a wrong subnet.
To compare it with bomac i have also started dmx-workshop.
See screenshot, please.
You need to correct it back to subnet 0, after you have chose it from that selection!
Or reduce the Amount to 3, to stay on letter F as biggest.
I will send MA a bug report.
Correct would be Art-Net addresses which where expected from bomac (which gma does not send):
0.D
0.E
0.F
1.0